DIY Bathtub Installation.
DIY Bathtub Installation.
Blog Article
Here in the next paragraph you can get lots of quality insight around Installing A Bathtub.
Installing a bath tub isn't specifically rocket science, however it does call for strong plumbing, woodworking, and in some cases, tiling abilities. Changing an old bathtub with a new one is likewise a reasonably difficult project. If the old tub is easily obtainable, the task can relocate quickly; if you have to open up a wall surface to get rid of the old bathtub and position the new tub, the job is a lot harder. In either instance, the task is within a home handyman's skills, although you will need a helper to leave the old tub as well as set in the new one. Ensure you have qualified yourself for the work and also fit trying it. As opposed to employing a specialist to take control of a halfway-completed task, it is far better to consider employing one before you begin. Chances are you may need a professional plumber to make tube connections.
This article will help you install a brand-new bath tub in your washroom if you have actually currently acquired a brand-new bathtub and also do not need to alter the plan of your previous supply of water pipes.
Your tools and product list need to consist of the following:
Preparing for the Installation
Firstly, the sustaining structure provided with the bath should be fitted (if required) according to the supplier's instructions. Next, fit the faucets or mixer to the bath tub. When suitable the tap block, it is important to make sure that if the faucet includes a plastic washer, it is fitted between the bathroom as well as the taps. On a plastic bath, it is additionally practical to fit a supporting plate under the taps device to avoid strain on the bath tub.
Fit the adaptable tap connectors to the bottom of both taps utilizing 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet with the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. See to it you make use of every one of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath should currently be ready to be suited its final setting.
Removing Old Taps
If you require to replace old faucets with new ones as a part of your setup, then the first thing you must do is disconnect the water system. After doing so, turn on the faucets to drain any kind of water staying in the system. The procedure of removing the existing faucets can be quite bothersome due to the limited access that is commonly the case.
Utilize a basin wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipelines to the taps. Have a fabric ready for the staying water that will certainly come from the pipes. As soon as the supply pipes have actually been gotten rid of, use the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single faucets from transforming during this process. As soon as the taps have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned up of any kind of old sealing compound.
Prior to moving on to fit the new taps, contrast the pipeline connections on the old taps to the new faucets. If the old faucets are longer than the new taps, then a shank adapter is required for the brand-new faucets to fit.
Installing the Tub
Utilizing both wooden boards under its feet, place the tub in the needed placement. The wooden boards are useful in equally spreading the weight of the bathtub over the area of the boards rather than concentrating all the weight onto 4 small points.
The next objective is to make sure that the bath tub is leveled all round. This can be achieved by checking the spirit level as well as changing the feet on the bath tub till the level reads level.
To install taps, fit the bottom of the furthest versatile faucet port to the proper supply pipeline by making a compression join; then do the same for the other tap.
Switch on the water and also examine all joints and also brand-new pipework for leakages and tighten them if essential. Load the tub as well as likewise check the overflow outlet and the regular electrical outlet for leakages.
Lastly, repair the bath paneling as defined in the maker's instruction manual. Tiling and securing around the tub ought to wait until the bathtub has actually been made use of a minimum of once as this will resolve it right into its final position.
Suitable New Touches
If the tails of the new taps are plastic, after that you will need a plastic adapter to stop damage to the thread. One end of the adapter fits on the plastic tail of the faucet and also the various other end supplies a connection to the existent supply pipes.
If you require to fit a monobloc, after that you will certainly need reducing couplers, which connects the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next, place the tap in the mounting opening in the bath/basin making sure that the washers are in area in between the tap and the sink. Secure the faucet in position with the producer provided backnut. As soon as the faucet is safely in place, the supply pipelines can be linked to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with normal faucet ports. The former kind ought to be connected to the faucet ends first, tightening up only by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Bathtub
In the location where the bath satisfies the tile, it is needed to seal the accompanies a silicone rubber caulking. This is important as the installation can move sufficient to crack a stiff seal, creating the water to permeate the wall surface between the bathroom and the tiling, causing complications with moisture and also possible leakages to the ceiling below.
You can select from a selection of coloured sealants to assimilate your components as well as installations. They are sold in tubes as well as cartridges, and also are capable of securing voids up to a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with twists of drenched paper or soft rope. Remember to always load the bathtub with water before securing, to permit the movement experienced when the bathtub remains in use. The sealant can split rather early if you do not take into consideration this activity prior to sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally conveniently available on the marketplace. It is advisable to fit the ceramic tiles making use of water-resistant or water resistant glue and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Hopefully you enjoyed our article about How to Install a Bathtub. Thank you for finding the time to read through our blog. Do you know about another person who is involved in the subject? Take a moment to share it. Many thanks for taking the time to read it.
Pricing Report this page